Did you remember to run your annual limited queries?

What’s happened?

A quick look at the rule’s development shows:

• 7/28/2025 — OSHA received a petition for rulemaking that covers obligations for ladder retrofits under 1910.28(b)(9).
• 9/15/2025 — OSHA posted a memo confirming it intends to eliminate 1910.28(b)(9)(i)(D).
• 12/18/2025 — OSHA sent its Walking-Working Surfaces (WWS) - Fixed Ladders proposal to the Office of Management and Budget (OMB) Office of Information and Regulatory Affairs (OIRA).
• 1/13/2026 — OIRA and OSHA met with the American Fuel and Petrochemical Manufacturers (AFPM).
• 1/21/2026 — OIRA and OSHA met with the Employers OSHA Modernization Coalition.
• 1/27/2026 — OIRA plans to meet with attorneys representing the American Petroleum Institute (API).

What did the petition request?

The seven-page petition, written by legal counsel on behalf of the AFPM, API, and American Chemistry Council (ACC), requests that OSHA:

• Withdraw the provision under the WWS standard for fixed ladders that extend more than 24 feet to be equipped with personal fall arrest systems (allowing the continued use of ladder cages or wells); or
• Grandfather fixed ladders installed before a particular date (authorizing the continued use of existing ladder cages or wells for those ladders).

Unjustified provision?

Petitioners argue that OSHA, in its 2010 proposed WWS rule, failed to:

• Take comments on the effectiveness of cages in protecting workers from falls,
• Disclose that the agency was evaluating whether to prohibit cages, and
• Give stakeholders a chance to submit evidence regarding cages.

The petition outlines the differences between the earlier proposed and final rules, noting that the 2010 proposal gave employers the choice to use any of four fall-protection types — cages, wells, ladder safety systems, or personal fall protection systems. However, the 2016 final rule gave a 2036 phase-out date for cages and wells.

The petition goes on to contend that:

• OSHA lacks sufficient evidence to justify prohibiting cages and wells;
• Data collected during the rulemaking process leaned toward preserving employer choices for fall protection; and
• Although the 2016 rulemaking preamble acknowledged the shift away from cages and wells, it did not fully discuss evidence in favor of cages and wells.

Other arguments in the petition

The petition raises several points questioning the benefits of paragraph (b)(9)(i)(D), stating that:

• In the past decade, AFPM, API, and ACC facilities have suffered only a few injuries, with no fatalities involving cages and wells;
• Cages offer passive protection, whereas ladder safety systems and personal fall arrest systems require workers to take action to comply;
• Personal protective equipment (PPE) lies at the bottom of the hierarchy of controls;
• Safety risks also exist for ladder safety systems and personal fall arrest systems; and
• Installing new ladders or retrofitting existing ones introduces hazards to those performing that work.

Finally, the petition addresses significant compliance costs, estimating several billion dollars for tens of thousands of ladders at U.S. refineries alone. Petitioners also cited additional expenses for rerating pressure vessels and engineering any process equipment changes.

What does OSHA say?

OSHA officially announced in a September 2025 memo that it is proposing to remove 1910.28(b)(9)(i)(D). The agency calls it a deregulatory action in line with Executive Order 14192. The memo reasons, “OSHA anticipates this change will allow employers to update their ladders when the ladders reach the end of their service lives, accommodating the lengthy service life of fixed ladders, while significantly reducing costs and offering greater flexibility.”

The WWS - Fixed Ladders proposal reached OIRA on December 18. OIRA typically takes 90 to 120 days for review, but recently a maximum 28-day review period for deregulatory actions was implemented. That means we anticipate OIRA will rush this proposal, so that OSHA may publish it in the Federal Register.

Key to remember

An upcoming OSHA proposal would withdraw 1910.28(b)(9)(i)(D). The rule was spurred by a petition.

When captured dust becomes a regulated waste

Under the Environmental Protection Agency (EPA) regulations, most collected dust qualifies as a solid waste once it’s removed from a dust collector, hopper, or filter. And despite the name, “solid waste” doesn’t mean solid, benign, or harmless. It simply means a discarded material.

At that point, facilities are expected to determine whether the dust is hazardous or non-hazardous under the Resource Conservation and Recovery Act (RCRA). This determination is based on what the dust contains, not how dusty it looks or how long it has been managed that way. Dust generated from metalworking, surface coatings, chemical processing, plastics, or specialty manufacturing can contain regulated constituents such as heavy metals or chemical residues. In these cases, facilities are required to make a waste determination using process knowledge, testing, or a combination of both.

This step is often overlooked. Many companies assume that if dust has not caused problems in the past, it must be non-hazardous. Unfortunately, regulators do not accept assumptions as documentation. If there’s no clear waste determination on file, that alone can be cited during an inspection. Misclassifying dust can also have ripple effects. If collected dust is later found to be hazardous, the facility may face issues related to improper disposal, incorrect generator status, or even cleanup liability at the disposal site. What began as a routine housekeeping task can suddenly become a significant compliance issue.

Storage, disposal, and the risks of getting it wrong

Even when dust is correctly identified as non-hazardous, it still needs to be managed properly. Open containers, poor labeling, and inconsistent handling practices are common findings during inspections. These issues are often viewed as minor, but they can quickly escalate if dust is released, mixed with other waste streams, or stored improperly.

Recycling adds another layer of complexity. Many facilities recycle metal dusts or other recoverable materials, which can be a smart environmental and economic decision. However, recyclable doesn't mean unregulated. Dust being recycled still needs to be stored safely, managed to prevent releases, and documented as legitimate recycling. Without proper controls, regulators may view the material as improperly managed waste.

Outdoor storage creates additional risk. Dust stored outside, transferred outdoors, or tracked out of the building can easily become a stormwater concern. Even non-hazardous dust can be considered a pollutant if it migrates off-site during rain events. This is a frequent source of violations under stormwater permits and Stormwater Pollution Prevention Plans (SWPPPs), especially when dust management isn’t addressed in the SWPPP.

Another common issue is mixing dust with general trash or other waste streams. Once mixed, otherwise manageable dust can become more difficult or impossible to classify correctly. This can complicate disposal, increase costs, and raise questions during audits or inspections.

What makes dust especially challenging is that responsibility for it often falls into a gray area. The safety team may assume that the environmental team is managing disposal. The environmental team may assume that the safety team has already classified the material. When no one clearly owns the waste determination and disposal process, gaps are almost guaranteed.

The most effective facilities treat dust as a waste stream that deserves the same attention as any other regulated material. They document waste determinations, define storage and labeling requirements, train employees on proper handling, and periodically revisit those determinations as processes change.

Keys to remember: Captured dust doesn’t stop being regulated once it leaves the air. Understanding whether collected dust is hazardous or non-hazardous, how it must be stored, and where it can legally go is essential to staying compliant.

Proposed legislation

Bipartisan legislation has recently been introduced in the House that would require businesses to provide restroom access to truckers who are loading or delivering cargo at their warehouses, manufacturers, distribution centers, retailers, and ports.

Supported by leading organizations in the trucking industry, the Trucker Bathroom Access Act (H.R. 9592) was introduced on Dec. 15, 2022. The bill requires retailers, warehouses, and other establishments with existing restrooms to provide access to drivers who are loading or delivering cargo. Additionally, operators of ports and marine terminals must provide access for drayage and parking while accessing such restrooms.

This amendment to Title 49 would exempt some employers from the bill including filling and service stations, and restaurants 800-square feet or smaller with restrooms intended for employee use only. The bill doesn’t require employers to construct new restrooms but to give truck drivers the same access as employees or customers.

Your restroom availability affects their health

Commercial truckers and delivery drivers are the lifeline of our supply chain of supplies, products, and consumables. Working tirelessly all hours, during holidays and weekends, and throughout the pandemic, they continue to deliver critical food and emergency supplies to companies everywhere. Employers have the privilege of demonstrating gratitude to truckers and delivery drivers with a positive work environment.

The benefits of allowing truckers and delivery drivers the convenience and safety of readily available, sanitary restroom facilities are plenty. They’re able to rest and reset when necessary, which keeps them and others safer on the roads. Equally important, restroom availability prevents drivers from having to search for available facilities elsewhere, allowing them to keep a timely delivery schedule, limit supply chain delays, and ultimately lower costs for employers and customers.

Keys to remember

The proposed Trucker Bathroom Access Act will require retailers, warehouses, and other establishments with existing restrooms to provide access to truckers and delivery drivers who are loading or delivering cargo. Access to restrooms keeps them refreshed and ready to deliver essential supplies to companies across the country.

For-hire vs. private

For-hire carriers use vehicles to transport people or property and are paid for their service. The fee could be a direct fee like a fare or a rate but could also be other indirect forms of compensation. Examples of for-hire operations include a trucking company that hauls other people’s property for a fee (direct compensation) or a hotel that includes in its service the transportation to and from the airport to the hotel (indirect compensation).

Private carriers, on the other hand, transport only their own goods or people. Examples include a manufacturer that uses its own commercial vehicles to transport its product, a construction or landscaping company that uses commercial vehicles to transport equipment and employees to job sites, or a utility company that operates commercial vehicles in support of its operations.

For-hire operating authority

While private carriers are not required to obtain operating authority from the FMCSA, for-hire carriers are required to get authority to move property or people that belong to somebody else and get paid for their service. Having authority is often referred to as having an MC Number.

The most common types of authority are:

• Property for-hire
• Passenger for-hire
• Household goods
• Broker
• Freight forwarder

If a company never operates a commercial motor vehicle (CMV), it is possible to have authority, but not have a USDOT number. For example, straight brokers or freight forwarders.

As part of obtaining for-hire authority, carriers must designate process agents and demonstrate financial responsibility (have proper insurance coverage).

One size does not fit all

Authorities are not all-inclusive. Separate authority is needed for each type of service offered. For instance, a for-hire, over-the-road carrier that also wants to be able to resell its extra demand will need both for-hire and brokerage authorities. A company is required to pay a $300 one-time fee for each type of authority needed.

Permanent authority required

There are no temporary permits available to substitute for authority. For-hire operations may not be performed until the proper authority has been granted. It’s not uncommon for otherwise private carriers to become for-hire carriers to generate revenue on back-hauls or help balance capacity and demand during slow periods or seasons.

Getting it right

Carriers need to get it right when it comes to authority. Carriers required to have authority — but don’t and operate anyway — can get themselves into trouble. Penalties for operating without proper authority can get expensive and can result in out-of-service orders.

A restart

The rescheduling proposal would move marijuana to the same drug class as prescription drugs such as Tylenol with codeine, ketamine, and steroids. It would also make it possible for medical marijuana to be prescribed to patients.

While the executive order revives the marijuana rescheduling issue, it will likely be 6-12 months before a final rule is issued.

Hearings will need to be scheduled, and comments from the hearings will need to be considered before a final rule is published.

DOT drug testing

A lot must happen before any changes will occur under the U.S. Department of Transportation (DOT) drug testing regulations. The DOT is required to follow U.S. Health and Human Services (HHS) guidelines for DOT drug testing, including the drug testing panel.

Until the federal Drug Enforcement Administration acts on rescheduling marijuana, neither the HHS nor DOT can move forward. Changes to the DOT drug testing panel can’t occur until:

• The HHS provides new guidelines, and
• Regulation 49 CFR Part 40 is revised through the rulemaking process.

At this time, it’s unknown whether there will be any stipulations built into the rescheduling allowing the HHS and DOT to continue testing for marijuana.

Stay the course for now

As the process plays out, employers not covered by federal drug and alcohol testing regulations should continue to follow state medical marijuana laws and watch for updates on workplace drug policy implications.

More will be known about how this executive order will influence workplace drug policies after hearings are completed and a final rule is issued. It’s likely that state laws will continue to make an impact on how employers handle marijuana in the workplace, however.

Key to remember: The federal government is once again looking at moving marijuana to a lower classification of drug. Until a final rule is issued, employers should continue to follow their current workplace drug policies. DOT testing panel may see changes, unless stipulations are built into rulemaking. The transportation industry anxiously waits to see how Executive Order will (or will not) impact DOT testing.

A Smarter Start

Motus is only as effective as the data that feeds into it, which is why FMCSA is emphasizing the importance of maintaining an active FMCSA Portal account. Carriers should log in today to confirm their account status or create one if they have never used the Portal before. Many carriers who have held authority for years may not realize they even have a Portal account, making this step especially important.

Once your account is active, you will be able to claim your USDOT Number in Motus and start managing your information there. Without this, users will not be able to complete registration updates or manage authority once the new system goes live. The FMCSA Portal login page allows users to sign in with existing credentials or start fresh through the online registration option, ensuring every company has a verified and secure entry point into Motus.

What to do now

One of the most important preparation steps is verifying the Portal user access list. Under the Account Management tab, companies should confirm which individuals have Portal access and identify their Company Official.

FMCSA is clear about who this person should be:

• The company owner, or
• An internal employee responsible for safety and compliance tasks

It should not be a consultant, third-party service provider, or transportation broker. The Company Official should use the same Login dot.gov email in both the FMCSA Portal and Motus. Using one consistent email ensures the systems can recognize the correct user and properly connect the company’s existing USDOT information to its new Motus account.

This one-to-one match is the only way FMCSA can securely link a company’s historical USDOT data with its new Motus account. Taking time now to verify the correct individual is listed can prevent access issues and delays during the transition.

Update your MCS-150 

Motus aims to create a centralized, accurate registration environment. To support that goal, FMCSA recommends carriers complete an online Biennial Update (MCS 150) in the Portal before Motus launches.

Submitting an update, or confirming no changes are needed, ensures the most current company information transfers into the new system. This includes:

• Operating status
• Fleet size and vehicle types
• Hazmat activity
• Mileage and safety data

Accurate information today means fewer issues when Motus goes live.

Key to remember: By getting ahead of these updates, you set your company up for a seamless shift into Motus when it launches.

8 levels of inspection

The CVSA has eight levels of roadside inspections. Each level has a varying degree of emphasis and detail. Although Roadcheck 2026 will involve mostly Level I comprehensive driver/vehicle inspections, drivers (and their vehicles) should be prepared for all inspection types every day of the year.

• Level I: Comprehensive driver/vehicle: Examination of driver documents, plus a detailed inspection of the vehicle.
• Level II: Cursory driver/vehicle: Examination of driver documents, plus a simple inspection of the vehicle.
• Level III: Driver: Examination of documents and items related to the driver.
• Level IV: Targeted: A one-time examination of a specific item, such as a driver’s record of duty status or a vehicle component.
• Level V: Vehicle: Detailed inspection of the vehicle only.
• Level VI: Radioactive cargo: Inspection of certain types of radioactive cargo.
• Level VII: Jurisdictional: An inspection mandated by a jurisdiction that doesn’t meet the requirements of any other level of inspection.
• Level VIII: Electronic: Conducted wirelessly or remotely, not necessarily requiring interaction with an inspector.

What are adverse driving conditions?

The Federal Motor Carrier Safety Administration (FMCSA) defines adverse driving conditions as weather or road conditions that could not have been known at the time of dispatch. This exception is meant to cover unexpected events, things a driver could not reasonably plan around. If conditions were forecasted, the ADC exception does not apply.

What does the exception allow?

When adverse conditions arise unexpectedly, a driver can drive up to 2 additional hours after the limits have been reached. Extending the driving time does not decrease the rest requirements. The exception cannot be used if the driver would not have been able to arrive on time, under normal conditions.

If a driver begins a trip and several hours into a trip, an unpredicted storm drops visibility, ADC may be used to complete the trip. A blizzard that was in the forecast for several days, would not qualify for this exception because the conditions were predicted in advance.

What is an Emergency Relief Order?

EROs are issued by state or federal authorities during significant events affecting public safety or essential supply chains. These orders temporarily modify HOS rules for drivers providing direct emergency assistance. Common examples of when these orders would be issued in the summer are:

• Widespread freezing temperatures that cause energy shortages,
• Major storms that disrupt supply chains and,
• Emergency transport of essential items like fuel, food and, medical supplies.

What does an ERO allow?

Each order is different, but they may allow:

• Temporary suspension of some or all HOS limits,
• More flexibility for drivers hauling emergency-related freight and,
• Apply across and entire state or region.

EROs should only be used when an official declaration is in place. Time limits are placed on these orders, so it is important to stay informed. The driver must be carrying emergency-related freight and, the carrier should notify the driver when they can and cannot use the exception.

Safety first, safety always

Neither of these exceptions override safety. Even with extra driving time, drivers should make good choices.

• Slow down in snow and ice,
• Increase following distance,
• Stop if conditions become unsafe and,
• Never drive fatigued.

The law gives flexibility in special circumstances, but it never removes the driver’s responsibility to operate safely.

Key to remember: Winter brings unique challenges for commercial drivers, but knowing the difference between Adverse Driving Conditions and Emergency Relief Orders helps ensure you stay safe, legal, and prepared.

Federal law

Under the federal Fair Labor Standards Act (FLSA), employers may deduct overpayments from employees’ future wages, even if that would result in the employees being paid below the minimum wage.

Big lump-sum deductions, however, might not sit well with employees, risking negative employee relations and trust.

State laws

Just because the federal FLSA allows related deductions, many state laws have limits on how much employers may deduct.

In California, for example, employers may not make deductions to recover overpayments unless the employer and employee have a written agreement, and the employee voluntarily consents to the deduction. The deduction also can’t cause the employee’s pay to fall below the state’s minimum wage.

An ounce of prevention

To help prevent overpaying employees, employers may take a few steps, such as the following:

• Automate payroll processes as much as possible;
• Audit all related processes and tools regularly;
• Have clear timekeeping and payroll policies; and
• Encourage employees to review their payments and paystubs regularly, and ask them to report any issues quickly so mistakes can be resolved.

Key to remember: Mistakes happen, including those that result in overpaying employees. Employers can, however, take steps to fix them and prevent them from recurring.

Focus on filing

A good place to start the organizational process is by auditing employee files. Employee personnel files need to be organized in a manner that allows for quick access, whether electronic or paper files. The information also needs to be as complete as possible.

These files might be the source of a company’s defense if an employee ever decides to lodge a complaint with a government agency or file a suit against the employer. If the information isn’t accessible or complete, an agency representative could see this as the employer’s noncompliance with a law, or a judge may see this as a lack of evidence of fair employee treatment.

No matter how HR professionals organize their files, some information must NOT be included in the general employee files. Employee and applicant medical information, for example, must be kept separate and confidential.

3 focus areas to start getting more organized this year

1. FLSA recordkeeping. The federal Fair Labor Standards Act (FLSA) has certain recordkeeping requirements. The FLSA doesn’t require a particular form for the records, but does require that the records include certain identifying information about each employee and data about the hours worked and the wages earned. The law requires this information to be accurate. Basic payroll and identifying employee data include such information as:

• Name,
• Address,
• Occupation,
• Rate or basis of pay and terms of compensation (i.e., benefits),
• Daily and weekly hours worked per pay period,
• Additions to or deductions from wages, and
• Total compensation paid.

Employers must keep payroll records and collective bargaining agreements for at least 3 years. Records on which wage computations are based should be kept for 2 years. This would include such data as time cards, wage rate tables, work and time schedules, records of additions to or deductions from wages, etc. These records must be open for inspection by the government representatives, and may be kept at the place of employment or in a central records office.

2. EEOC recordkeeping. The federal Equal Employment Opportunity Commission (EEOC) regulations require that employers keep all personnel or employment records for 1 year. If an employee is involuntarily terminated, their personnel records must be retained for 1year from the date of termination. Additionally, employers must keep any employee benefit plan (such as pension and insurance plans) and any written seniority or merit system for the full period the plan or system is in effect and for at least 1 year after its termination.

3. FMLA recordkeeping. Covered employers are required to make and keep records about the company’s obligations under the Family and Medical Leave Act (FMLA) in accordance with the FLSA recordkeeping requirements. The FMLA also refers to the confidentiality provisions of the Americans with Disabilities Act and Genetic Information Nondiscrimination Act of 2008. Generally, employers must keep FMLA-related records for at least 3 years. No particular order or form of the records, however, is required. Other FMLA information to keep includes such details as:

• Dates when employees take FMLA leave. Employers may want to include copies of timesheets or records, written requests for leave, etc.
• Specific hours of leave if it’s taken in increments of less than one full day.
• Written copies of employee notices of leave they give to the employer and copies of all required general and specific written notices given to employees.
• Any documents, including written and electronic records, describing employee benefits or a company’s policies and practices regarding the taking of paid and unpaid leave.
• Premium payments for employee benefits.
• Records of any disputes between the employer and an employee regarding the designation of leave as FMLA leave, including any written statement from the employer or employee of the reasons for the designation and for the disagreement.

The bottom line

Remember, employers may keep records either electronically or have physical paper copies, but either method needs to be locked down and kept secure. Only designated personnel should be able to access the information within the rules of each applicable law.

It’s also good to set up a “purge” schedule to go through and discard old records once the time requirements have passed.

Key to remember: If getting more organized is a goal for this year, January’s a great time to get started. Focusing on the recordkeeping requirements of the FLSA, EEOC, and FMLA can help set the tone for the year.

1. Maintain required records

Section 380.725 of the Federal Motor Carrier Safety Regulations (FMCSRs) lists the specific records that must be maintained by all ELDT providers on FMCSA’s Training Provider Registry (TPR). During an ELDT audit the investigator will ask for and review the following ELDT-specific records:

• Self-certifications by all behind-the-wheel driver-trainees stating that they will comply with:
  • The regulations in Parts 40, 382, 383, and 391; and
  • State and/or local laws related to alcohol and controlled substances testing, age, medical certification, licensing, and driver records;
• A copy of the driver-trainee’s commercial learner’s permit (CLP) or commercial driver’s license (CDL);
• Instructor qualification documentation:
  • Listing each instructor’s driving and/or training experience, and
  • A copy of each instructor’s current and valid CDL and applicable endorsements;
• Lesson plans for theory and behind-the-wheel (range and public road) training curricula; and
• Records of each driver-trainee’s ELDT assessments.

2. Ensure TPR data is current

Another issue being addressed is the activity or inactivity within the ELDT provider’s TPR profile. To remain on the TPR, an ELDT provider needs to periodically update its data on the TPR. This includes:

• Updating the Entry-Level Driver Training Provider Registration Form at least once every two years (biennially); and
• Reporting changes to key information to FMCSA within 30 days of the change. This includes changes to the:
  • Training provider’s name, address, or phone number;
  • Type(s) of training offered; and
  • Training provider’s status, and, if applicable, any change in state licensure, certification, or accreditation status.

3. Meet any applicable state requirements

In addition to the ELDT requirements, many states have requirements that must be met by schools and entities providing CDL instruction. In many cases these requirements apply to schools or entities that offer instruction for tuition or a fee.

As part of the process to be listed on the TPR, a school or entity certifies that they are licensed, certified, registered, or authorized to provide training as required by the laws and regulations of the state where in-person training is conducted.

During an audit, the investigator will ask for documentation of state licensure, registration, or certification to verify that the provider is authorized to provide training in the state. This also confirms that the school or entity correctly certified that they are meeting state requirements on their TPR application.

Key to remember: Ensuring that all records are complete and up to date is key when it comes to having a successful ELDT audit.

No driver’s license but must be 18 years old

Since forklifts are not operated on public roads, the operator does not need a driver’s license. In fact, OSHA requires training on the differences between a forklift and a car. Someone with a driver's license might assume that forklifts handle like cars, but they do not!

A forklift operator must, however, be at least 18 years old. That’s not in the OSHA regulations, but appears in the child labor regulations. Minors under 18 years of age cannot operate (or even ride on) equipment like forklifts or scissor lifts.

Seatbelts required

Everyone knows that forklift operators must use the seatbelt if the forklift has one. That does not appear in the OSHA standard, but it’s usually a safety warning in the forklift operator manual. Since failing to wear a seat belt is a recognized hazard that could cause serious injury, OSHA uses the General Duty Clause to cite employers that don’t enforce seatbelt use.

Hearing or vision impairments

Employers occasionally hire trainees with hearing loss, vision impairment, or other physical limitations. Alternatively, an experienced forklift operator could get injured or experience similar impairments. OSHA does not establish specific requirements for vision, hearing, or other qualifications, and physical limitations are not necessarily disqualifying.

Instead, employers must evaluate the individual and determine if the person can operate safely. Trainers should work with their Human Resources team to evaluate possible accommodations under the Americans with Disabilities Act. Do not assume that a physical limitation would prevent someone from becoming a safe forklift operator. If an evaluation finds that the person cannot meet acceptable safety standards, the employer may refuse to certify the operator.

Trainers might need training

The employer determines who is qualified to deliver powered industrial truck training. The trainer must have the “knowledge, training, and experience” to train and evaluate operators. Attending a “train the trainer” class and getting a certification isn’t a bad idea, but OSHA doesn’t require any particular course or certification to be a trainer.

OSHA does, however, require that the trainer have experience using the type of equipment that trainees will operate. Since experience is required, the trainer likely received training on using that equipment. Further, if the employer purchases a new type of truck or attachment that the trainer has never used, the trainer will need experience using that equipment before training others.

For related information, see our articles on Debunking the mysteries of forklift training (Part 1) and Debunking the mysteries of forklift training (Part 2).

Even minor modifications require approval

Modifications that affect “safe operation” require the manufacturer’s written approval per 1910.178(a)(4). In OSHA’s view, that covers nearly any change, even adding a warning light or backup alarm. A Letter of Interpretation dated April 11, 1997, clarified that if the manufacturer does not respond or refuses to approve a modification, employers may instead get approval from a Qualified Registered Professional Engineer. Employers should ensure that forklift operators don’t modify equipment, like adding plywood or tarps to the cage as a sun shade. Those changes could affect safe operation and would require approval.

Key to remember: The powered industrial truck standard does not address every issue that employers might face, but employers can find answers in other regulations or guidance.

What is remote ID?

A remote ID broadcasts a drone’s identification and location information. Law enforcement and federal agencies need access to this information quickly when a drone is flying in an unsafe manner or in a restricted area. It enables them to locate the drone’s control station.

The requirement can be met in one of three ways.

1. Standard remote ID drone: The remote ID capability is built into the drone. The drone broadcasts the following from takeoff to shut down:
   • Remote ID-compliant serial number
   • Location and altitude
   • Velocity
   • Control station location and elevation
   • Time mark
   • Emergency status
2. Remote ID broadcast module: Remote ID capability is met through attaching a module to the drone. This option, however, is limited to visual-line-of-sight operations. The module broadcasts the following from takeoff to shut down:
   • Remote ID-compliant serial number
   • Location and altitude
   • Velocity
   • Takeoff location and elevation
   • Time mark
3. FAA-Recognized Identification Area (FRIA): Drones without remote ID can operate without broadcasting, providing they fly within a visual line of sight and an FRIA. FRIAs are sponsored by community-based organizations and educational institutions.

Who is subject to the drone rule?

All drone pilots who are required to register with FAA must follow the remote ID requirements. The regulation impacts those operating drones for recreation, business, or public safety.

When pilots register with FAA, they must list the serial number(s) of each Standard Remote ID drone and/or the Remote ID broadcast module.

Key to remember: Aviation safety and security is not limited to manned aircraft. To effectively respond to hazards posed by drones, the agency must be able to locate and identify the craft.

Employer rights/responsibilities after an OSHA inspection

OSHA inspections can be an overwhelming experience. Understanding the regulatory terms and what’s required of you afterwards can be confusing. OSHA says its Employer Rights and Responsibilities Following a Federal OSHA Inspection booklet can and should be used as a discussion guide during your closing conference with the compliance officer.

The booklet explains that:

• After an inspection, the officer reports the findings to the OSHA area director who evaluates them.
• If a violation was found, OSHA will issue you a Citation and Notification of Penalty detailing the exact nature of the violation(s) and any associated penalties. A citation informs you of the alleged violation. It also sets a proposes an abatement date and penalty amounts.

Also explained in OSHA’s guidance are types of violations, employer options, how to comply, how to contest citations, and more. The booklet is available as a pdf or ebook in English and Spanish.

Nail salon hazards and prevention strategies

Nail technicians are exposed to hazardous chemicals found in glues, polishes, removers, and other salon products. The trouble is these exposures can lead to asthma and other respiratory illnesses, skin disorders, liver disease, reproductive loss, and cancer. Additionally, awkward positions and repetitive motions may lead to muscle strains, and workers face potential infections from contact with client skin, nails, or blood.

Stay Healthy and Safe While Giving Manicures and Pedicures: A Guide for Nail Salon Workers highlights common issues in nail salons — such as chemical and biological exposures, ventilation problems, inadequate personal protective equipment (PPE), and ergonomic risks. Importantly, the guide provides practical steps for correcting those issues. It also explains worker rights and offers a list of applicable OSHA standards and resources. The publication is available in five languages.

Redline-strikeout version of 2024 HazCom rule

Finally, OSHA returned the redline-strikeout version of its 2024 HazCom rule to its Hazard Communication topic page. The latest document includes the corrections issued in the Federal Register (on May 20, 2024, October 9, 2024, January 8, 2026, and January 15, 2026). The redline-strikeout version is the full text of 29 CFR 1910.1200 with all revisions from 2024 and 2026 marked in red so you can spot what was added, revised, or removed.

We anticipate more HazCom guidance and enforcement information will be coming to OSHA’s HazCom topic page, either behind the HCS final rule link or the other links on the page.

Key to remember: OSHA continues to update its guidance publications. The latest ones cover OSHA inspections, nail salon safety, and hazard communication.

The explosive truth in one month

Two southern factories are great examples of how safety “hints” can turn deadly when not enough attention is given to workplace warnings. A Tennessee factory and a Kentucky plant both could have possibly averted October 2025 catastrophes, by looking a little further into signs and symptoms of existing dangers.

Tennessee OSHA (TOSHA) had cited a munitions factory with safety violations six years prior to its October 10th explosion after investigating why multiple employees were having seizures and other symptoms of dangerous chemical exposures.

Air monitoring confirmed that employees likely weren’t exposed to explosive cyclonite powder through inhalation. However, the inspection revealed that employees were not adequately protected from exposure through ingestion or skin absorption. Inspections found that employees were being exposed to surface contamination and ingestion risks from being allowed to consume food and beverages without proper hygiene practices being enforced.

The U.S. Chemical Safety and Hazard Investigation Board (CSB), working closely with the Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF), are still investigating the fatal explosion. The ATF believes the blast originated where mixed explosive materials were heated in production kettles followed by additional explosions occurring on the same floor of the facility after the original blast.

Just north and a few days earlier, an explosion occurred at a Kentucky chemical plant thought to be caused by an overflow of calcium carbide from a furnace. Though OSHA and local law enforcement continue to investigate, a preliminary review revealed that the calcium carbine actually landed on the ground, contributing to the explosion.

Though the explosion didn’t result in any fatalities, the same factory had experienced an explosion in March 2011 that did claim the lives of two workers while injuring two others. The CSB concluded the explosion was due to an electric arc furnace that over-pressurized, ejecting solid and powdered debris, flammable gases, and molten calcium carbide toward the workers. Accumulations of hazardous carbide and water were also thought to have contributed to the incident.

Looking back

In retrospect, if each employer had identified the potential for an explosive environment, based on prior incidents and employee exposures, and taken appropriate protective measures, the events of October 2025 could have been avoided.

By performing thorough investigations into how explosive materials were accumulating, and by implementing necessary changes to eliminate exposure risks, almost 20 lives might have been saved, and numerous serious injuries as well as extensive damage to both facilities could have been prevented.

Employers can reduce the risk of workplace explosions and fatalities by adopting a proactive approach that includes comprehensive safety protocols through:

• Performing workplace risk assessments and process hazard analysis;
• Conducting regular inspections to ensure proper ventilation and housekeeping;
• Managing ignition sources and flammable materials by using appropriate storage and handling procedures;
• Implementing explosion prevention systems that detect, isolate, and suppress explosive conditions;
• Maintaining infrastructure and equipment by addressing sparking concerns, faulty wiring, leaks, and instrumentation malfunctions;
• Training employees in recognizing explosion risks and safe work practices;
• Promoting a safe work culture through preparedness training, committees, and other employee engagement; and
• Complying with OSHA and other related standards.

Key to remember: Ignoring safety warnings not only endangers lives but also leads to preventable tragedies that impact employees and their families, operations and the community, and often, organizational reputation.