CDL/non-CDL and the short-haul exceptions: What’s the difference?

What’s happened?

A quick look at the rule’s development shows:

• 7/28/2025 — OSHA received a petition for rulemaking that covers obligations for ladder retrofits under 1910.28(b)(9).
• 9/15/2025 — OSHA posted a memo confirming it intends to eliminate 1910.28(b)(9)(i)(D).
• 12/18/2025 — OSHA sent its Walking-Working Surfaces (WWS) - Fixed Ladders proposal to the Office of Management and Budget (OMB) Office of Information and Regulatory Affairs (OIRA).
• 1/13/2026 — OIRA and OSHA met with the American Fuel and Petrochemical Manufacturers (AFPM).
• 1/21/2026 — OIRA and OSHA met with the Employers OSHA Modernization Coalition.
• 1/27/2026 — OIRA plans to meet with attorneys representing the American Petroleum Institute (API).

What did the petition request?

The seven-page petition, written by legal counsel on behalf of the AFPM, API, and American Chemistry Council (ACC), requests that OSHA:

• Withdraw the provision under the WWS standard for fixed ladders that extend more than 24 feet to be equipped with personal fall arrest systems (allowing the continued use of ladder cages or wells); or
• Grandfather fixed ladders installed before a particular date (authorizing the continued use of existing ladder cages or wells for those ladders).

Unjustified provision?

Petitioners argue that OSHA, in its 2010 proposed WWS rule, failed to:

• Take comments on the effectiveness of cages in protecting workers from falls,
• Disclose that the agency was evaluating whether to prohibit cages, and
• Give stakeholders a chance to submit evidence regarding cages.

The petition outlines the differences between the earlier proposed and final rules, noting that the 2010 proposal gave employers the choice to use any of four fall-protection types — cages, wells, ladder safety systems, or personal fall protection systems. However, the 2016 final rule gave a 2036 phase-out date for cages and wells.

The petition goes on to contend that:

• OSHA lacks sufficient evidence to justify prohibiting cages and wells;
• Data collected during the rulemaking process leaned toward preserving employer choices for fall protection; and
• Although the 2016 rulemaking preamble acknowledged the shift away from cages and wells, it did not fully discuss evidence in favor of cages and wells.

Other arguments in the petition

The petition raises several points questioning the benefits of paragraph (b)(9)(i)(D), stating that:

• In the past decade, AFPM, API, and ACC facilities have suffered only a few injuries, with no fatalities involving cages and wells;
• Cages offer passive protection, whereas ladder safety systems and personal fall arrest systems require workers to take action to comply;
• Personal protective equipment (PPE) lies at the bottom of the hierarchy of controls;
• Safety risks also exist for ladder safety systems and personal fall arrest systems; and
• Installing new ladders or retrofitting existing ones introduces hazards to those performing that work.

Finally, the petition addresses significant compliance costs, estimating several billion dollars for tens of thousands of ladders at U.S. refineries alone. Petitioners also cited additional expenses for rerating pressure vessels and engineering any process equipment changes.

What does OSHA say?

OSHA officially announced in a September 2025 memo that it is proposing to remove 1910.28(b)(9)(i)(D). The agency calls it a deregulatory action in line with Executive Order 14192. The memo reasons, “OSHA anticipates this change will allow employers to update their ladders when the ladders reach the end of their service lives, accommodating the lengthy service life of fixed ladders, while significantly reducing costs and offering greater flexibility.”

The WWS - Fixed Ladders proposal reached OIRA on December 18. OIRA typically takes 90 to 120 days for review, but recently a maximum 28-day review period for deregulatory actions was implemented. That means we anticipate OIRA will rush this proposal, so that OSHA may publish it in the Federal Register.

Key to remember

An upcoming OSHA proposal would withdraw 1910.28(b)(9)(i)(D). The rule was spurred by a petition.

What’s changing and why it matters

Although EPA has been deregulating or loosening some requirements, there are still some standards being tightened across multiple fronts in the coming year:

• Renewable fuel standards (RFS): The EPA proposed higher volume requirements for 2026, including 24.02 billion renewable identification numbers (RINs), up nearly 8% from 2025. This increase pushes stricter expectations on fuel producers and organizations purchasing renewable fuels.
• Stormwater multi-sector general permit (MSGP): A new MSGP set to take effect by February 2026 will require quarterly PFAS indicator monitoring, expanded benchmark sampling, and resiliency measures in stormwater control designs.
• PFAS Reporting under the Toxic Substances Control Act (TSCA): TSCA Section 8(a)(7) mandates PFAS manufacturing and import data collection beginning in April 2026, through October 2026, with extended deadlines for certain small manufacturers.

Failure to prepare could lead to fines, reputational damage, supply chain disruptions, and permit delays. Companies that weave compliance planning into their 2026 strategy will be positioned not just to meet legal deadlines but to sustain operations smoothly.

Key areas of impact

• Renewable fuel standards (RFS) and air emissions The proposed increase in 2026 Renewable Identification Numbers (RIN) volumes, from 24.02 billion to 24.46 billion for 2027, signals tightening air and fuels policy that affects fuel use and emissions accounting.
• Stormwater management The upcoming 2026 MSGP requires expanded quarterly PFAS monitoring, new benchmark triggers, corrective action plans, and integration of climate resilience in design standards.
• PFAS disclosure (TSCA Section 8(a)(7)) Manufacturers and importers of PFAS must submit electronic reporting of usage, volumes, disposal, and exposure data between April and October 2026, with extensions available for smaller operations.

Steps to take now

• Audit compliance programs: Cross-check operations against RIN inventory, stormwater permits, and TSCA reporting duties.
• Upgrade monitoring and recordkeeping: Implement robust electronic systems to track PFAS, stormwater quality, fuel volumes, and emissions.
• Staff training: Educate teams on PFAS obligations, new stormwater protocols, and RFS structures.
• Engage regulators early: Comment on proposed rules, consult during permit drafting, and flag issues during the notice-and-comment period.

Looking ahead

The EPA’s 2026 updates reflect a trend toward increased transparency and environmental accountability. Companies that treat compliance as strategic will not only avoid enforcement but also gain resilience and stakeholder trust.

Key to remember: Start planning now. Early action on EPA rule changes will save time, money, and headaches when enforcement begins.

More than just rules

The order covers not only final and proposed regulations but also “notices of inquiry,” any type of notice of proposed rulemaking, and guidance documents that interpret existing statutes or regulations.

The order will be overseen by the director of the White House Office of Management and Budget (OMB), a position to which Trump has nominated Russ Vought.

OMB wastes no time

The OMB, which must approve most rulemaking activities, has already sent numerous pending rules back to the agencies for review. Among the rules withdrawn on January 21, 2025:

• A proposal to update the new-driver training regulations to address sexual harassment and the safety of women truck drivers and vulnerable road users, such as pedestrians and bicyclists.
• A proposal to amend the Federal Motor Carrier Safety Regulations to account for the use of trucks and buses equipped with automated driving systems.
• A proposal from the Department of Health and Human Services to implement hair testing for federal workers.
• Proposed railroad noise-emission enforcement rules from the Federal Railroad Administration.
• A proposed air-emissions reporting requirement from the Environmental Protection Agency (EPA), as well as proposed EPA standards for emissions from PFAS manufacturing facilities.

In addition, the Occupational Safety and Health Administration withdrew a proposed rule on infectious diseases on January 14 and its COVID-19 healthcare rule on January 15, prior to the inauguration.

President Trump issued a similar regulation freeze upon his 2017 inauguration. Soon after, he announced a “two for one” order requiring agencies to eliminate two regulations for every new one issued.

What prevents workers from reporting?

The Centers for Disease Control and Prevention (CDC) completed a study that revealed several reasons employees are reluctant to report a bloodborne pathogen exposure. These include:

• Being unsure of what constitutes a bloodborne pathogen, an exposure, or a potential exposure;
• Worrying reporting may result in a negative performance review;
• Knowing they weren’t wearing the proper personal protection equipment (PPE);
• Fearing discipline, retaliation, or loss of their job;
• Having concerns about confidentiality;
• Feeling guilty that the exposure may have been their fault;
• Believing that wiping blood or other body fluids off their clothes or skin prevents exposure; and
• Wanting to avoid taking time away from work to report an exposure.

Protecting the workforce

Protecting workers is as simple as 1-2-3. Employers should ensure workers follow these guidelines:

1. Avoid close, skin-to-skin contact and contact with sharp objects when caring for an injured person.
2. Avoid contact with objects and materials that may contain blood or OPIMs.
3. Practice effective personal hygiene and workplace sanitation by cleaning and disinfecting immediately after treating an injured person.

Employers can ensure worker protection by:

• Training workers on the hazards of bloodborne pathogen exposures, the health consequences if left untreated, proper hygiene and sanitation protocols, and how to report exposures;
• Ensuring workers are familiar with existing emergency protocols and the locations of emergency eyewash stations or showers and first aid stations;
• Instituting and communicating a post-exposure evaluation process;
• Assuring employees that reports will not adversely affect their employment or performance evaluations and that reports are handled confidentially;
• Establishing a mandatory policy to immediately report all exposures or potential exposures;
• Providing appropriate protective equipment and supplies, such as gloves, masks, sharps containers, and disinfection and hazardous material disposal supplies;
• Implementing a system for reporting that is efficient to use and maintains confidentiality;
• Issuing regular reminders to workers to report all exposures to blood and other body fluids; and
• Cultivating a positive safety culture that promotes trust, care, and protection for everyone.

Keys to Remember

Employers must protect workers from the risk of exposure to bloodborne pathogens. This includes protecting responders from illness or hospitalization resulting from unreported exposures. Protecting workers requires continual communication of hazards, proper training and supplies, assurance of accountability, and a positive safety culture.

What this means for California/CARB

The California Air Resources Board (CARB) may continue state-level enforcement of CTC for all in-state, out-of-state, and foreign-registered vehicles. However, they cannot claim SIP credit for emissions reductions from vehicles not registered in California.

What this means for trucking companies

Trucks not registered in California may still be subject to California enforcement, but EPA will not enforce those requirements federally. California cannot use those inspections or emissions reductions for SIP compliance.

Compliance options for testing

To comply with CARB’s CTC requirements, trucking companies can choose from multiple emissions testing options. Those options include:

• A telematics-based approach: The telematics option is a “set-it-and-forget-it” onboard diagnostics (OBD) test option. With this option, once the telematics device is set up on the vehicle, required data is automatically submitted to CARB.
• Hiring a credentialed tester to perform compliance testing: There are more than 30,000 credentialed testers, 15,000 of which are for hire. The “Credentialed Tester List - CTC-VIS” website features real-time updates to the list.
• Checking out a testing device from specified locations: Anyone can become a credentialed tester by taking the Tester Training Course and passing the exam in the Clean Truck Check-Vehicle Inspection System (CTC-VIS). Fleets can then perform the testing in-house without the need to hire third-party testers.
• Permit option: Finally, for vehicles that rarely operate in California, the HD I/M Regulation includes a five-day pass provision that allows any vehicle in the fleet to be operated in California for up to five consecutive days once per year without meeting the requirements of the rule.

FAQ: Does this regulation apply to my truck or fleet?

CTC applies to almost all diesel, alternative fuel, and hybrid vehicles, with a gross vehicle weight rating over 14,000 pounds, operating on public roads and highways in California — even if they are not registered in California. This includes:

• Government vehicles;
• Motorcoaches;
• Transit, shuttle, and school buses;
• Hybrid vehicles;
• Commercial and personal use vehicles;
• California registered motorhomes; and
• Single-vehicle fleets.

Freight contractors and brokers must:

• Only contract with compliant vehicles or fleets, and
• Comply with the record keeping requirements.

Ports and railyards also have requirements regarding CTC compliance status of vehicles and access to their facility.

Key to remember: EPA’s recent action does not end California’s CTC program. CARB enforcement continues, and trucks operating in the state are still required to comply with all program requirements.

How the NRII process works (and why delays happen)

Under the NRII, medical examiners must enter a driver’s exam result into the National Registry no later than the end of the next calendar day. The FMCSA then sends these results to the appropriate SDLA so the information can be posted to the CDL MVR.

The most frequent source of delays is data-entry errors in the examiner’s electronic medical card (MCSA5850). Mistakes in key identifying information — such as name, date of birth, CDL number, or state of licensure — prevent the SDLA from validating the submission. When this happens, examiners receive an email alert but must correct the error before the SDLA can receive and post the record.

The FMCSA recognized early that MVR update delays were widespread, which led to several waivers. The current waiver, effective January 11 through April 10, 2026, allows carriers and drivers to rely on paper medical cards for up to 60 days after the exam.

Best practices for drivers and carriers

Proactive steps can significantly reduce both delays and compliance disruptions. Consider implementing the following:

1. Schedule exams early.

Encourage drivers to complete their exams at least two weeks before their certification expires. Maintain internal reminders to ensure drivers promptly report exam results and share a copy of their medical card.

2. Verify license information at the end of the exam.

Ask drivers to confirm that their personal information — name, date of birth, CDL number, and licensing state — matches what appears on the medical examination report (MCSA5876). Incorrect CDL formatting continues to be one of the most common causes of the NRII upload failures.

3. Request and retain a paper medical card.

Even though examiners aren’t required to issue a paper medical card, the FMCSA recommends that they do so during the NRII transition. Drivers should receive a paper card as these are legal proof of certification for up to 60 days under the current waiver and help prevent them from being placed out of service. A copy should go in the driver qualification file to be replaced by the updated MVR within 60 days.

4. Check MVRs within 2–5 days after each exam.

Early monitoring helps identify issues while examiners may be more receptive and able to quickly correct errors.

How to troubleshoot delayed MVR updates

The FMCSA recommends following a structured, three step troubleshooting process:

Step 1: Contact the medical examiner.

Confirm that they addressed any National Registry validation errors and resubmitted the MCSA5850. This is the most common issue that’s easily resolved.

Step 2: Reach out to the SDLA’s CDL help desk.

If issues pop up, carriers and drivers should contact the CDL help desk, not the general help line. Ideally, the call should include both a knowledgeable carrier representative and the driver. Begin by explaining that the examiner has already corrected any errors. Then request that the SDLA’s medicalcertification team “pull” the record directly from the National Registry.

Step 3: Contact the FMCSA Registry Support team if needed.

If steps 1 and 2 don’t resolve the issue, carriers and drivers should contact the FMCSA Registry Support team:

Phone: (617) 4943003

Email: fmctechsup@dot.gov

If the problem still isn’t resolved, carriers and drivers should document the steps taken to show good-faith efforts were made. If the driver’s MVR doesn’t update within the waiver period, to reduce the risk of having a disqualified driver citation, carriers should consider removing them from CMV driving until the MVR updates.

Key to remember: When carriers and drivers proactively manage medical exam timing and closely track MVR updates, they are less likely to face disqualification surprises or other compliance issues.

To-do before October 1

Get ready for renewal by taking the following steps now:

• File all your highway use tax returns that are due.
• Pay your taxes. The state will not issue a new certificate of registration if you owe back taxes. Before you apply to renew, make sure that you’ve paid all taxes due under any of the programs administered by the New York State Tax Department, including:
  • HUT,
  • personal income tax,
  • International Fuel Tax Agreement (IFTA),
  • sales tax, and
  • withholding tax.
• Create an online account if you do not already have one and you want to renew your credentials and pay online (https://www.oscar.ny.gov/).
• Make sure your vehicle registration information is correct and accurate. Review and update your information as soon as possible. Incorrect information will delay the processing of your certificates and decals.

Beginning October 1

Once the renewal period opens, renew your credentials and pay your renewal fees online with One Stop Credentialing and Registration (OSCAR).

Submit your renewal application by November 30, 2024, to make sure you receive your decals in time to place them on your vehicles before January 1, 2025.

If you are already enrolled in OSCAR, use your current OSCAR password to renew online.

If you are not enrolled, visit OSCAR, and select Enroll Now. You must have a United States Department of Transportation (USDOT) number and an employer identification number (EIN).

To renew your registration:

1. Visit the OSCAR website and select HUT Renewal from the Business Type drop-down.
2. Enter your information in the USDOT#, NYS Tax ID#, and Password fields, then select Log in.
3. If you have 300 or fewer vehicles, choose either:
   1. Renew all HUT/AFC Certificates of Registration to renew all your active current series permits, or
   2. Select HUT/AFC Certificates of Registration to renew specific permits.
4. If you have more than 300 vehicles, choose either:
   1. Renew all to renew all your active current series permits, or
   2. File renewal to renew select permits.

If you are unable to renew electronically, you may file Form TMT-1.2, Renewal Application for Highway Use Tax (HUT) and Automotive Fuel Carrier (AFC) Certificates of Registrations and Decals – 25th Series.

Key to remember: Take steps now to renew your NY HUT and ensure you receive your new decals before the current ones expire.

The courts weigh in

After being dismissed from the hiring process, the applicant sued the trucking company, arguing that the rejection violated Pennsylvania’s Criminal History Record Information Act. The Act is a state law that defines how employers can use a person’s criminal past when making hiring decisions. Under the law, employers must:

• Show that a conviction relates to whether someone can do the job in question, and
• Put it in writing if they turn down an applicant based on criminal history.

A district court threw out the case, saying that the law applies only when employers obtain criminal records from state agencies, not when applicants disclose information themselves.

The U.S. Court of Appeals for the Third Circuit disagreed. In reversing the lower court’s decision, the judge explained that the statute focuses on what kind of information an employer receives, not where it comes from. The law protects information that is part of someone's criminal history record, regardless of the source.

The key distinction, the court found, is between the type of information and its origin. When the applicant disclosed his robbery conviction, the company received information that exists in his criminal history record file maintained by state agencies. That triggered the law's protections, even though the company learned about it directly from the applicant rather than through an official background check. 

No impact on ‘ban-the-box’ laws

The trucking company argued that interpreting the law this way would make legislation known as “ban-the-box” laws meaningless. Local ban-the-box ordinances prohibit employers from asking about criminal history on job applications. But the court rejected that reasoning. Pennsylvania's law doesn’t stop employers from asking about convictions; it just limits what they can do with the answers. Ban-the-box laws are another layer of protection cities can choose to require.

The company also tried to use an exception in the statute for information from certain public sources like court documents and police blotters. The court wasn’t persuaded by this argument because even if that exception applied to hiring discrimination claims, it doesn’t cover what an applicant voluntarily shares. The law lists specific exempted sources, and by omitting applicant disclosures from that list, the legislature signaled they shouldn’t be exempt. 

The decision sent the case back to the lower court, where the company will have to defend its actions. That means the trucking company must show why the applicant’s robbery conviction makes him unsuitable to drive their trucks, and whether the company provided proper written notice when it turned him down. 

Employers, especially those in Pennsylvania, New Jersey, Delaware, and the Virgin Islands – the states covered by the Third Circuit – should be aware that this ruling clarifies that criminal history laws apply uniformly. The protections don’t disappear if an applicant chooses to be honest during the hiring process. 

Key to remember: A federal circuit court ruled that learning about a criminal conviction from a job applicant triggered the same legal protections as learning about it through an official background check during the hiring process. 

Submitting employees to drug tests

Can motor carriers drug test their drivers? The short answer is no. Canada does not have a federal regulation that requires drug testing for drivers. However, this does not mean that Canadian motor carriers cannot implement and enforce a drug and alcohol policy for their drivers. In fact, many carriers have developed successful policies that minimize the risk of getting in trouble with the law and ensure the safety of their drivers and the public.

For the most part, drug testing not only violates the Human Rights Code, but it is also a gross infringement on an individual’s reasonable right to protection of privacy. Motor carriers operating in Canada need to make sure they consider the human rights and privacy rights of their drivers when implementing any type of drug testing program and policy.

Motor carriers have the right to expect their drivers to arrive at work fit for duty and remain that way throughout the duration of their shift. Communicating this expectation to them is important and, at a minimum, should be communicated by implementing a ”fit-for-work” policy that makes your expectations around impairment of any kind clear.

When drug testing may be permissible

There are some circumstances in which drug testing is allowed, though they are rare and very specific.

1. Safety-sensitive positions: Universal random drug testing would be acceptable in workplaces that can be shown to be extremely dangerous and where a worker’s impairment would likely result in catastrophe. Based on this definition commercial truck drivers would be considered to be in a safety-sensitive position.

2. Reasonable suspicion of impairment: If an employee appears to be obviously impaired, drug testing may be permissible, especially if they’re involved in a collision and there is reasonable suspicion that they are under the influence of drugs.

3. As part of a rehabilitation/return-to-work program: A driver with substance abuse disorder may be subject to unannounced drug testing to be carried out as part of a rehabilitation program and return-to-work program.

Unlike in the United States, pre-employment drug testing is generally not permitted in Canada, except in limited circumstances. Each Canadian province has its own legislation regarding testing for drugs. In Alberta, the courts have been less protective of individual privacy rights and have allowed drug testing in the oil and gas sector. Most companies in Ontario and British Columbia opt not to test for drugs, adhering to human rights legislation and privacy concerns.

Policies must be clear

Motor carriers must inform their drivers about the drug and alcohol policy and unlike U.S. testing programs, are required to obtain their consent before conducting any test. By working together, motor carriers and drivers can create a safe and healthy work environment for everyone involved.

Carriers should update their policies addressing drug and alcohol use at least once per year. Carriers must pay close attention to:

• Permissible testing for the jurisdictions they operate in, including if they cross the border into the United States;
• Frequent reminders for drivers on their obligations under the policies; and
• Training for managers and supervisors on detecting impairment through physical symptoms.

Key to remember: Drug testing in Canada is legal but not regulated, so carriers must exercise caution when implementing a drug testing policy. There’s a fine line between allowable testing and human rights/employee privacy violations.

Case in point

In April, Toby, an employee, applied for FMLA leave for his chronic kidney stones. The certification indicated that he would need intermittent leave up to 3 times per month for 1 day per episode.

Things went fine until August 23, when Toby asked for time off. The conversation went something like this:

• Toby: Can I have a personal day tomorrow because my kids are starting a new school?
• Employer: Let me see if one’s available. It’s not available for tomorrow.
• Toby: Well, okay. I guess you’ll have to put me on FMLA leave then.
• Employer: OK, so FMLA for your kids’ school event.
• Toby: Thank you.

Toby ended up taking 4 days of medical leave.

Based on the phone conversation, the employer charged Toby with FMLA misuse and removed him from work pending an investigatory hearing.

At the hearing, Jolanda, the company’s FMLA manager, said it was clear, based on the conversation, that Toby “….marked off FMLA for an unapproved reason”—so clear that “[t]here wasn’t a need” for the company to “determine if the leave that [Toby] requested was actually used for FMLA protection or for purposes of the FMLA.”

Toby said that he needed to be off both because his kids were starting a new school and because his medical condition had started to flare up. He explained that he initially asked for a personal day, rather than FMLA leave, so he would be paid for the day and could avoid using up his FMLA time.

Toby said he saw a doctor for his flare-up and provided a doctor’s note dated August 24. The note said that Toby had been under a doctor’s care from August 24 to 27.

After the hearing (and despite the doctor’s note), the employer concluded that Toby had misused FMLA leave and fired him.

Toby sued, and the court sided with him, disagreeing with the employer’s argument that Toby had misused FMLA leave. Toby had enough evidence to establish that the employer’s decision to fire him wasn’t “reasonably informed and considered….”

The employer’s only basis for believing Toby misused FMLA leave was his phone call. The call didn’t conclusively establish that Toby engaged in misconduct, especially given his testimony that he needed to deal with both medical needs and family obligations. The doctor’s note also provided evidence that Toby’s request for leave was legitimate.

Pack v. CSX Transportation, Inc.; Southern District of West Virginia; No. 3:24-0688; January 14, 2026.

Key to remember: Employers should look at all the facts of a situation before concluding that an employee abused FMLA leave.

Topics and worker types covered

Topics addressed by these bills include musculoskeletal disorders, heat stress, infectious diseases, wildfire smoke, and workplace violence. Federal OSHA does not have comprehensive standards for any of those hazards. Some existing standards are related — sanitation, first aid, personal protective equipment, and injury/illness recordkeeping and reporting.

Without comprehensive standards, OSHA may turn to enforce these hazards under the General Duty Clause (GDC), Section 5(a)(1) of the Occupational Safety and Health Act. Yet, the GDC poses a high bar for inspectors. OSHA can only cite under Section 5(a)(1) if the alleged hazard: exists, is recognized, is serious, and has a feasible means to reduce that hazard.

If any one of the four criteria is missing, a GDC citation will not hold. On the other hand, putting a standard in place both mandates protections and makes it much easier for OSHA to cite employers for the hazards.

Worth noting, some of the bills specifically cover domestic workers, firefighters, warehouse workers, public sector workers, and healthcare and social service workers.

Nine bills to watch

Below are the nine Congressional bills (and companions) currently under consideration:

• LET’S Protect Workers Act, H.R. 6597 — Introduced 12/10/2025. This bill would raise civil monetary penalties for employers that violate occupational safety and health requirements. Willful and repeat violations would jump to $800,000 each. The bill would also direct OSHA to close a loophole that prevents citations for failing to maintain required injury and illness records if the violation is not discovered within six months. Instead, every day an employer fails to make or maintain a record during the five-year record retention period would be a violation.
• Domestic Workers Bill of Rights Act, S. 3396 and H.R. 3971 — Introduced 12/9/2025 and 6/12/2025, respectively. This bill would require a board to make recommendations to OSHA for standards that affect the well-being of domestic employees, including infectious diseases protections.
• Healthy Lungs for Heroes Act, S. 3183 — Introduced 11/18/2025. This bill would require OSHA to develop an appropriate exposure limit for wildfire smoke for wildland firefighters and supporting staff where current PELs are not a good fit for wildfire situations. The bill would also require the incorporation by reference of a National Fire Protection Association standard on respirators for wildland fire-fighting operations.
• Warehouse Worker Protection Act, H.R. 4896 and S. 2613 — Introduced 8/5/2025 and 7/31/2025, respectively. This bill would require OSHA to publish a standard for ergonomic program management with elements including hazard identification, job evaluations, hazard control, training, and medical management. The bill also calls for OSHA to publish a standard on first aid and employer-provided occupational medicine consultation services. Finally, it would update the Occupational Safety and Health Act (OSH Act) so a contest notice would not stay abatement of a violation.
• Asunción Valdivia Heat Illness, Injury, and Fatality Prevention Act, H.R. 4443 and S. 2298 — Both introduced 7/16/2025. These bills would require OSHA to promulgate a standard to protect workers from heat-related injuries and illnesses. Such a standard may have measures like engineering controls, administrative controls, personal protective equipment, medical and emergency protocols, training, and a written plan.
• Recognizing that climate change poses a growing threat to public health and necessitates coordinated action to mitigate its impacts and safeguard the health and well-being of all people in the United States, H.Res. 568 and S.Res. 318 — Both introduced 7/10/2025. These bills say that OSHA “should” promulgate a worker heat protection standard that, in accordance with the best available evidence, establishes the highest degree of health and safety protection feasible.
• Protecting America’s Workers Act, H.R. 3036 — Introduced 4/28/2025. This bill would require OSHA to update its incorporations by reference of national consensus standards, with some exceptions. The bill makes other changes to the OSH Act to expand coverage to public sector workers, increase protections, and raise penalties.
• Safe Workplaces Act, H.R. 2647 — Introduced 4/3/2025. This bill taps OSHA to issue nonmandatory guidance on activities and work practice controls that can be implemented at work to reduce workplace violence.
• Workplace Violence Prevention for Health Care and Social Service Workers, H.R. 2531 and S. 1232 — Both introduced 4/1/2025. These bills mandate OSHA to issue a standard that requires covered employers within the healthcare and social service industries to develop and implement a comprehensive workplace violence prevention plan. The plan must include procedures and methods for risk assessment and identification of risks, hazard prevention and controls, reporting and investigation, emergency response, and training.

Key to remember

Several bills in Congress would modernize the OSH Act and mandate OSHA rulemaking to strengthen or increase worker protections.

Sampling results

Testing for a hazardous substance in Subpart Z would create an exposure record. Those regulations cover asbestos, lead, chromium, formaldehyde, and many other substances. In addition, the tables in 1910.1000 list hundreds of substances from carbon dioxide to vegetable oil mist. Testing for harmful substances that are not listed could also create an employee exposure record.

In addition, measuring noise, vibration, temperature extremes, or particulate matter will usually create an exposure record that must be retained for 30 years. However, measurements of conditions in a normal range (such as office temperature readings) are not exposure records under the OSHA standard.

Not every sample or measurement will create an exposure record. OSHA clarified that exposure records describe the identity of, and possibly the level of exposure to, a toxic substance or harmful physical agent. For example, if an indoor air quality evaluation sampled the HVAC system, the results might identify non-toxic bacteria typical in office or work environments. That result would not be an employee exposure record.

Known hazards

If employers test for a substance with known human health effects, OSHA considers the results to be an employee exposure record even if the levels are below a listed action level or permissible exposure limit (PEL). The term “employee exposure record” is not limited to records showing that exposure exceeds a particular level, but rather on the mere fact that occupational exposure exists. For example, testing for carbon dioxide levels would create an exposure record even if the results were well within safe parameters.

Of course, if exposures are below the action level, the employer can usually stop monitoring, unless a process or work practice changes in a way that could increase exposure. However, if exposures are above the action level but below the PEL, employers may need to conduct periodic monitoring, all of which become exposure records.

On the other hand, the standard does not cover situations where the employer can demonstrate that the toxic substance or harmful physical agent is not used, handled, stored, generated, or present in the workplace in any manner different from typical non-occupational situations.

Finally, OSHA notes that employee questionnaires are not exposure records because they don’t characterize exposures. For example, employers might survey the workforce about things like comfort, temperature, or similar conditions without actually measuring conditions.

However, if questionnaires address medical information, they can be “employee medical records” under 1910.1020. For instance, the questionnaire under the respiratory protection standard is a medical record, but not an exposure record. OSHA also requires maintaining certain medical records. For more information, see our article, Who retains employee medical records?

Key to remember: Employers must save employee exposure records of hazardous substances even if the measured amount was within acceptable levels.

Total hours worked

Determining the total hours worked probably involves your Human Resources or payroll department. They key is to count only hours worked, not hours paid. Do not include vacation, sick leave, holidays, or other non-working time even if employees were paid for that time. If some employees are not paid the by the hour (such as salaried or commission employees) you can estimate their total hours.

The total hours are used to calculate the Total Recordable Incident Rate (TRIR), or incident rate, which is expressed as a ratio of injuries per 100 workers. For instance, a rate of 2.3 means that for every 100 employees, 2.3 employees had recordable injuries.

However, the incident rate is actually a ratio of injuries per 200,000 hours worked (representing 100 employees working 40 hours per week for 50 weeks). This allows OSHA to compare locations regardless of part-time staff, since the rate depends on hours worked, not on the number of people. This is also why employers don’t count vacation or holiday hours; employees cannot get work-related injuries during those hours.

Key to remember: Correctly calculating your workforce size and total hours worked ensures an accurate 300A summary and incident rate.

Inspection failure

If the operator skips or rushes through the pre-shift inspection, safety concerns could get overlooked. Problems with systems like hydraulics, brakes, or steering can obviously contribute to accidents. However, even things like a non-functioning horn or lights could increase the likelihood of collisions.

Also, operators must report any problems that arise during the shift. If a pre-shift inspection identifies failures, the problem likely occurred during the previous shift and perhaps could have been reported. Equipment failures more likely occur during operation, not during idle time between shifts. If something goes wrong mid-shift, the operator must remove the truck from service. Make sure operators know how to report problems, send the truck for service, and obtain an alternate vehicle for the remainder of the shift.

Carrying loads too high

Operators should carry loads as low as possible. During inspections, OSHA compliance officers commonly see loads carried too high. This limits both visibility and stability. When the load size restricts visibility and the truck cannot travel in reverse (like going up a ramp), the operator should use a spotter.

Similarly, operators must never raise or lower a load while moving or turning. Doing so increases the risk of accidents from falling loads. Also, driving while watching the load (not the road) can increase the risk of striking pedestrians or objects.

Driving too fast

Employers might communicate speed limits, but most forklifts don’t have speedometers. Therefore, operators should understand what constitutes safe (and unsafe) speeds under various conditions. In locations with pedestrians or limited visibility, this might mean at walking speed, which can seem painfully slow.

OSHA compliance officers can issue citations for excessive speed. Excessive speed increases the risk of spilling a load, striking a pedestrian, and rollover potential.

Not certified for truck type

Forklift operators must receive training that covers the types of vehicles used. An operator trained on a sit-down counterbalanced forklift needs additional training to operate a stand-up model or even a powered pallet jack. A supervisor might be able to explain the controls for a different vehicle type, but that does not constitute “training” and certainly not certification. OSHA commonly issues citations for lacking operator certification.

In addition, employers must evaluate each operator’s performance every three years. Typically, this involves questioning the operator on safety rules and observing the operator performing typical duties. If the evaluation identifies problems, the employer must provide refresher training. Skipping this evaluation could result in a failure to identify violations that contribute to accidents.

An operator who is not certified for the vehicle type may lack understanding of critical handling characteristics or safety precautions, which increases the risk of accidents.

Key to Remember: When forklift operators feel under time pressure, they might focus on speed over safety. Skipping the inspection, driving too fast, raising loads while moving, and other behaviors put the operator and other employees at risk.

Employer injury/illness reporting

OSHA has limited ability to focus inspection and compliance efforts where they’re most needed because it has not effectively enforced its mandatory injury and illness reporting requirements for employers, the report contends. In fact, a September 2023 OIG audit found that on average, between 2016 and 2020, nearly 60 percent of establishments in all industries failed to report their annual injury and illness data to OSHA.

The report went on to say that:

• OSHA could not identify if an establishment met the reporting criteria. This meant the agency could not effectively cite employers for non-compliance or proactively remind specific establishments that they must report.
• Employer under- and non-reporting produces an incomplete view of workplace injury and illness. This, in turn, makes it difficult for OSHA to identify high-risk establishments to target.

Since the 2023 report, OSHA’s Tracking rule took effect January 1, 2024, with an added reporting category — establishments with 100 or more employees in industries designated as very high-risk. These establishments must submit data from the Forms 300, 301, and 300A annually. OSHA explains that it has updated its data collection capabilities. This includes new applications to analyze individual case reports of establishment-specific data.

The Inspector General report urges OSHA to complete its initiatives to improve employer reporting of injuries and illnesses. Meanwhile, each year, OSHA publicly posts employer injury and illness data reported under 1904.41.

Fewer inspectors, fewer inspections

Reaching millions of worksites is an ongoing challenge because the number of federal inspectors is going down, not up, DOL OIG charges, citing 846 in February 2024 and 736 in June 2025. Along with its state partners, in 2026 OSHA will have approximately 1,720 inspectors, or about one inspector for every 84,000 employees. Inspector numbers may continue to decline due to retirements, resignations, and other reductions.

The Inspector General puts it bluntly, “A lack of available inspectors can lead to fewer inspections, diminished enforcement in high-risk industries and ultimately, greater risk of fatalities, injuries, or compromised health for workers.”

It should be stated that fiscal year (FY) 2026 appropriations were approved and signed into law on February 3, 2026. The latest funding is: $243,000,000 for federal enforcement and $120,000,000 for OSHA State-Plan states.

• These numbers are unchanged from FY 2025 for federal OSHA enforcement, but slightly higher for state plans. While the funding is not lower than previous years, inflation limits how far OSHA can go with its dollars. Unchanged funding doesn’t necessarily translate to keeping the same number of inspectors.

Workplace violence

Although fatalities due to workplace violence plummeted about 13 percent from 2022 to 2023, workplace violence remains a top five leading cause of employee death, according to OIG. OSHA doesn’t have a standard addressing this issue but has relied instead on the General Duty Clause (GDC) for enforcement since 1993.

The agency must consider actions to address and prevent workplace violence, the Inspector General stresses. Such actions may include a rulemaking. OIG announced plans to perform an audit to determine the effectiveness of the GDC in OSHA’s enforcement efforts, including workplace violence.

Last summer, OSHA slid its Workplace Violence in Health Care and Social Assistance proposed rulemaking to the long-term regulatory agenda items without explanation. Any upcoming OIG results showing the GDC is ineffective for workplace violence may pressure OSHA to issue a regulation and/or fast forward its existing proposal.

The latest OIG report is not the first time the watchdog has recommended OSHA do something about workplace violence. It was noted in a November 2023 report, and an entire September 2001 report was devoted to the issue. Additionally, a 2016 Government Accountability Office (GAO) report outlined “additional efforts” OSHA should take to protect healthcare workers from workplace violence.

Two workplace violence bills currently in Congress would call on OSHA to take action on the issue. See 9 OSHA bills to mandate gap-closing rules, wider coverage, steeper fines.

Key to remember: A recent OIG report addresses what it calls OSHA’s most pressing challenges — annual injury/illness reporting, fewer inspectors, and workplace violence — and what the agency must do going forward to meet them.