FREE TRIAL UPGRADE!
Thank you for investing in EnvironmentalHazmatHuman ResourcesHuman Resources, Hazmat & Environmental related content. Click 'UPGRADE' to continue.
CANCEL
YOU'RE ALL SET!
Enjoy your limited-time access to the Compliance Network!
A confirmation welcome email has been sent to your email address from ComplianceNetwork@t.jjkellercompliancenetwork.com. Please check your spam/junk folder if you can't find it in your inbox.
YOU'RE ALL SET!
Thank you for your interest in EnvironmentalHazmatHuman ResourcesHuman Resources, Hazmat & Environmental related content.
WHOOPS!
You've reached your limit of free access, if you'd like more info, please contact us at 800-327-6868.
CLOSE
 
 

...

ASTM D86 Standard test method for distillation of petroleum products and liquid fuels at atmospheric pressure

RegSenseProcess Safety ManagementEnforcement and Audits - OSHAHazard ClassificationsFlammable LiquidsConsensus StandardsIndustry Consensus StandardHazard CommunicationEnglishEnforcement and Audits - OSHASafety & HealthGeneral Industry SafetyToxic and Hazardous Substances - OSHAASTM InternationalHazardous Materials Safety - OSHAHazard CommunicationFocus AreaToxic and Hazardous Substances - OSHAUSA

This standard provides a test method that covers the atmospheric distillation of petroleum products using a laboratory batch distillation unit. This method is used to determine, quantitatively, the boiling range characteristics of such products.

Current edition

  • ASTM D86-18 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure

Incorporation by reference

The following editions have been incorporated by reference (IBR) into the Code of Federal Regulations (CFR):

IBR approved for Overview of requirements IBR approved edition
29 CFR 1910.106(a)(5)As used in 1910.106, boiling point   means the boiling point of a liquid at a pressure of 14.7 pounds per square inch absolute (p.s.i.a.) (760 mm.). Where an accurate boiling point is unavailable for the material in question, or for mixtures which do not have a constant boiling point, for purposes of 1910.106 the 10 percent point of a distillation performed in accordance with the Standard Method of Test for Distillation of Petroleum Products, ASTM D-86-62, may be used as the boiling point of the liquid.ASTM D86-62 Test for Distillation of Petroleum Products.
29 CFR 1910.119(b)Where an accurate boiling point is unavailable for the material in question, or for mixtures which do not have a constant boiling point, the 10 percent point of a distillation performed in accordance with the Standard Method of Test for Distillation of Petroleum Products, ASTM D-86-62, may be used as the boiling point of the liquid.ASTM D86-62 Test for Distillation of Petroleum Products.
29 CFR 1910.1200 Appendix B.6.3The flash point shall be determined in accordance with ASTM D56-05, ASTM D3278, ASTM D3828, ASTM D93-08, or any other method specified in GHS Revision 3, Chapter 2.6. The initial boiling point shall be determined in accordance with ASTM D86-07a or ASTM D1078.ASTM D86-07a Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure.

How to purchase

Standards are available for purchase from the American National Standards Institute (ANSI), see webstore.ansi.org, and from ASTM International, see www.astm.org.

['Enforcement and Audits - OSHA', 'Toxic and Hazardous Substances - OSHA', 'Hazardous Materials Safety - OSHA', 'Hazard Communication']
['Toxic and Hazardous Substances - OSHA', 'Flammable Liquids', 'Hazard Classifications', 'Process Safety Management', 'Enforcement and Audits - OSHA', 'Hazard Communication']
UPGRADE TO CONTINUE READING
Load More