...
Standard Number: 1910.1200; 1910.1200(f)(1); 1910.1200(g)(1); 1910.1200(g)(2)
May 9, 2017
Mr. John P. Lenore
Quaker Chemical Corporation
13210 Barton Circle
Whittier, California 90605
Dear Mr. Lenore:
Thank you for your letter to the Occupational Safety and Health Administration (OSHA), Directorate of Enforcement Programs. Your letter requested clarification on labeling under the revised Hazard Communication standard (HCS 2012), 29 CFR 1910.1200. This letter constitutes OSHA’s interpretation only of the requirements herein, and may not be applicable to any questions not delineated within your original correspondence. Your paraphrased question and our response is below.
Background: Your company is in the process of developing a two-component material that would be distributed in a 120 milliliter (mL) pair of tubes containing 60 mL of Part A and 60 mL of Part B, for use by end users. Separate safety data sheets (SDSs) and labels are used in the manufacturing environment and in all situations where Parts A and/or B can be produced, stored, or distributed independently. The two tubes are attached as a dual cartridge that cannot be separated. The dual cartridge is designed to be inserted into a gun-type applicator and the two materials are intended to be squirted simultaneously and mixed through an orifice as it is squeezed onto the surface. The end user is only exposed to the mixture (barring container failure or deliberate misuse) for approximately five minutes until it hardens.
Question: Would it be acceptable to treat the two components as one mixture for the purpose of hazard communication to the end user (SDSs, labels, etc.)?
Response: No. OSHA considers each tube containing Part A and Part B to be separate containers, and therefore, each tube must be individually labeled in accordance with 29 CFR 1910.1200(f)(1). The HCS 2012 requires the manufacturer or importer to ensure that each container of hazardous chemicals leaving the workplace is labeled, tagged, or marked in accordance with 29 CFR 1910.1200(f)(1)(i)-(vi).
Additionally, section 1910.1200(g)(1) requires chemical manufacturers or importers to develop an SDS for each hazardous chemical they produce or import. Because Parts A and B are distinct chemicals in separate containers, an SDS is required for each chemical. Single SDSs are permitted only when components have similar hazards and contents (i.e., the chemical ingredients are essentially the same, but the specific composition varies from mixture to mixture). See 1910.1200, Appendix A.
When a manufacturer or importer intends for a chemical to be used with another chemical (e.g., two chemicals in dual containers will be mixed together, even for a short duration), and that use creates a new hazard, this information must be included on the SDSs for each hazardous chemical in the reaction products in Section 10(c) (Stability and reactivity) of the SDS. OSHA would require information on the safe handling and use of the reaction product in other sections of the SDS such as 4 (First-aid measures), 5 (fire-fighting measures), 6 (accidental release measures), 7 (handling and storage), and 8 (exposure controls/personal protection), if different than the individual components. See 1910.1200(g)(2).
As you may be aware, California is one of 26 states plus Puerto Rico and the Virgin Islands that operates its own occupational safety and health program under a plan approved and monitored by federal OSHA. Employers in California must comply with state occupational safety and health requirements. As a condition of plan approval, State Plans are required to adopt and enforce occupational safety and health standards that are at least as effective as those promulgated by federal OSHA. A state’s interpretation of their standards must also be as least as effective as federal OSHA interpretations. If you would like further information regarding California’s occupational safety and health requirements, you may contact California at the following address:
- Division of Occupational Safety and Health
- 1515 Clay Street, Suite 1901
- Oakland, CA 94612
- Telephone: (510) 286-7000; Fax: (510) 286-7037
Thank you for your interest in occupational safety and health. We hope you find this information helpful. OSHA’s requirements are set by statute, standards, and regulations. Our letters of interpretation do not create new or additional requirements but rather explain these requirements and how they apply to particular circumstances. This letter constitutes OSHA’s interpretation of the requirements discussed. From time to time, letters are affected when the Agency updates a standard, a legal decision impacts a standard, or changes in technology affect the interpretation. To assure that you are using the correct information and guidance, please consult OSHA’s website at http://www.osha.gov. If you have further questions, please feel free to contact the Office of Health Enforcement Programs at (202) 693-2190.
Sincerely,
Thomas Galassi, Director
Directorate of Enforcement Programs