['Water Programs']
['Maximum Contaminant Levels', 'Water Quality', 'Safe Drinking Water']
07/08/2024
...
(a) The following maximum contaminant levels for volatile organic contaminants apply to community and non-transient, non-community water systems.
CAS No. | Contaminant | MCL (mg/l) |
(1) 75-01-4 | Vinyl chloride | 0.002 |
(2) 71-43-2 | Benzene | 0.005 |
(3) 56-23-5 | Carbon tetrachloride | 0.005 |
(4) 107-06-2 | 1,2-Dichloroethane | 0.005 |
(5) 79-01-6 | Trichloroethylene | 0.005 |
(6) 106-46-7 | para-Dichlorobenzene | 0.075 |
(7) 75-35-4 | 1,1-Dichloroethylene | 0.007 |
(8) 71-55-6 | 1,1,1-Trichloroethane | 0.2 |
(9) 156-59-2 | cis-1,2-Dichloroethylene | 0.07 |
(10) 78-87-5 | 1,2-Dichloropropane | 0.005 |
(11) 100-41-4 | Ethylbenzene | 0.7 |
(12) 108-90-7 | Monochlorobenzene | 0.1 |
(13) 95-50-1 | o-Dichlorobenzene | 0.6 |
(14) 100-42-5 | Styrene | 0.1 |
(15) 127-18-4 | Tetrachloroethylene | 0.005 |
(16) 108-88-3 | Toluene | 1 |
(17) 156-60-5 | trans-1,2-Dichloroethylene | 0.1 |
(18) 1330-20-7 | Xylenes (total) | 10 |
(19) 75-09-2 | Dichloromethane | 0.005 |
(20) 120-82-1 | 1,2,4-Trichloro- benzene | .07 |
(21) 79-00-5 | 1,1,2-Trichloro- ethane | .005 |
(b) The Administrator, pursuant to section 1412 of the Act, hereby identifies as indicated in table 2 to this paragraph (b) granular activated carbon (GAC), packed tower aeration (PTA), or oxidation (OX) as the best technology, treatment technique, or other means available for achieving compliance with the maximum contaminant level for organic contaminants identified in paragraphs (a) and (c) of this section, except for per- and polyfluoroalkyl substances (PFAS).
BAT for Organic Contaminants Listed in §141.61(a) and (c)
CAS No. | Contaminant | GAC | PTA | OX |
15972-60-8 | Alachlor | X | ||
116-06-3 | Aldicarb | X | ||
1646-88-4 | Aldicarb sulfone | X | ||
1646-87-3 | Aldicarb sulfoxide | X | ||
1912-24-9 | Atrazine | X | ||
71-43-2 | Benzene | X | X | |
50-32-8 | Benzo[a]pyrene | X | ||
1563-66-2 | Carbofuran | X | ||
56-23-5 | Carbon tetrachloride | X | X | |
57-74-9 | Chlordane | X | ||
75-99-0 | Dalapon | X | ||
94-75-7 | 2,4-D | X | ||
103-23-1 | Di (2-ethylhexyl) adipate | X | X | |
117-81-7 | Di (2-ethylhexyl) phthalate | X | ||
96-12-8 | Dibromochloropropane (DBCP) | X | X | |
95-50-1 | o-Dichlorobenzene | X | X | |
106-46-7 | para-Dichlorobenzene | X | X | |
107-06-2 | 1,2-Dichloroethane | X | X | |
75-35-4 | 1,1-Dichloroethylene | X | X | |
156-59-2 | cis-1,2-Dichloroethylene | X | X | |
156-60-5 | trans-1,2-Dichloroethylene | X | X | |
75-09-2 | Dichloromethane | X | ||
78-87-5 | 1,2-Dichloropropane | X | X | |
88-85-7 | Dinoseb | X | ||
85-00-7 | Diquat | X | ||
145-73-3 | Endothall | X | ||
72-20-8 | Endrin | X | ||
100-41-4 | Ethylbenzene | X | X | |
106-93-4 | Ethylene Dibromide (EDB) | X | X | |
1071-83-6 | Gylphosate | X | ||
76-44-8 | Heptachlor | X | ||
1024-57-3 | Heptachlor epoxide | X | ||
118-74-1 | Hexachlorobenzene | X | ||
77-47-3 | Hexachlorocyclopentadiene | X | X | |
58-89-9 | Lindane | X | ||
72-43-5 | Methoxychlor | X | ||
108-90-7 | Monochlorobenzene | X | X | |
23135-22-0 | Oxamyl (Vydate) | X | ||
87-86-5 | Pentachlorophenol | X | ||
1918-02-1 | Picloram | X | ||
1336-36-3 | Polychlorinated biphenyls (PCB) | X | ||
122-34-9 | Simazine | X | ||
100-42-5 | Styrene | X | X | |
1746-01-6 | 2,3,7,8-TCDD (Dioxin) | X | ||
127-18-4 | Tetrachloroethylene | X | X | |
108-88-3 | Toluene | X | X | |
8001-35-2 | Toxaphene | X | ||
93-72-1 | 2,4,5-TP (Silvex) | X | ||
120-82-1 | 1,2,4-Trichlorobenzene | X | X | |
71-55-6 | 1,1,1-Trichloroethane | X | X | |
79-00-5 | 1,1,2-Trichloroethane | X | X | |
79-01-6 | Trichloroethylene | X | X | |
75-01-4 | Vinyl chloride | X | ||
1330-20-7 | Xylene | X | X |
(c) The following maximum contaminant levels (MCLs) in paragraphs (c)(1) and (2) of this section for synthetic organic contaminants apply to community water systems and non-transient, non-community water systems; paragraph (c)(2) of this section also contains health-based water concentrations (HBWCs) for selected per- and poly-fluoroalkyl substances (PFAS) used in calculating the Hazard Index.
(1) MCLs for Synthetic Organic Contaminants, Except for PFAS.
CAS No. | Contaminant | MCL (mg/l) |
---|---|---|
(i) 15972-60-8 | Alachlor | 0.002 |
(ii) 116-06-3 | Aldicarb | 0.003 |
(iii) 1646-87-3 | Aldicarb sulfoxide | 0.004 |
(iv) 1646-87-4 | Aldicarb sulfone | 0.002 |
(v) 1912-24-9 | Atrazine | 0.003 |
(vi) 1563-66-2 | Carbofuran | 0.04 |
(vii) 57-74-9 | Chlordane | 0.002 |
(viii) 96-12-8 | Dibromochloropropane | 0.0002 |
(ix) 94-75-7 | 2,4-D | 0.07 |
(x) 106-93-4 | Ethylene dibromide | 0.00005 |
(xi) 76-44-8 | Heptachlor | 0.0004 |
(xii) 1024-57-3 | Heptachlor epoxide | 0.0002 |
(xiii) 58-89-9 | Lindane | 0.0002 |
(xiv) 72-43-5 | Methoxychlor | 0.04 |
(xv) 1336-36-3 | Polychlorinated biphenyls | 0.0005 |
(xvi) 87-86-5 | Pentachlorophenol | 0.001 |
(xvii) 8001-35-2 | Toxaphene | 0.003 |
(xviii) 93-72-1 | 2,4,5-TP | 0.05 |
(xix) 50-32-8 | Benzo[a]pyrene | 0.0002 |
(xx) 75-99-0 | Dalapon | 0.2 |
(xxi) 103-23-1 | Di(2-ethylhexyl) adipate | 0.4 |
(xxii) 117-81-7 | Di(2-ethylhexyl) phthalate | 0.006 |
(xxiii) 88-85-7 | Dinoseb | 0.007 |
(xxiv) 85-00-7 | Diquat | 0.02 |
(xxv) 145-73-3 | Endothall | 0.1 |
(xxvi) 72-20-8 | Endrin | 0.002 |
(xvii) 1071-53-6 | Glyphosate | 0.7 |
(xxviii) 118-74-1 | Hexacholorbenzene | 0.001 |
(xxix) 77-47-4 | Hexachlorocyclopentadiene | 0.05 |
(xxx) 23135-22-0 | Oxamyl (Vydate) | 0.2 |
(xxxi) 1918-02-1 | Picloram | 0.5 |
(xxxii) 122-34-9 | Simazine | 0.004 |
(xxxiii) 1746-01-6 | 2,3,7,8-TCDD (Dioxin) | 3 × 10 8 |
(2) MCLs and HBWCs for PFAS.
CAS. No. | Contaminant | MCL (mg/l) (unless otherwise noted) | HBWC (mg/l) for Hazard Index calculation |
---|---|---|---|
1 The PFAS Mixture Hazard Index (HI) is the sum of component hazard quotients (HQs), which are calculated by dividing the measured component PFAS concentration in water by the relevant health-based water concentration when expressed in the same units (shown in ng/l for simplification). The HBWC for PFHxS is 10 ng/l; the HBWC for HFPO-DA is 10 ng/l; the HBWC for PFNA is 10 ng/l; and the HBWC for PFBS is 2000 ng/l. | |||
(i) Not applicable | Hazard Index PFAS (HFPO-DA, PFBS, PFHxS, and PFNA) | 1 (unitless) 1 | Not applicable. |
(ii) 122499-17-6 | HFPO-DA | 0.00001 | 0.00001. |
(iii) 45187-15-3 | PFBS | No individual MCL | 0.002. |
(iv) 108427-53-8 | PFHxS | 0.00001 | 0.00001. |
(v) 72007-68-2 | PFNA | 0.00001 | 0.00001. |
(vi) 45285-51-6 | PFOA | 0.0000040 | Not applicable. |
(vii) 45298-90-6 | PFOS | 0.0000040 | Not applicable. |
Hazard Index = ([HFPO-DA water ng/l]/[10 ng/l]) + ([PFBS water ng/l]/[2000 ng/l]) + ([PFNA water ng/l]/[10 ng/l]) + ([PFHxS water ng/l]/[10 ng/l])
HBWC = health-based water concentration
HQ = hazard quotient
ng/l = nanograms per liter
PFAS water = the concentration of a specific PFAS in water
(d) The Administrator, pursuant to section 1412 of the Act, hereby identifies in table 3 to this paragraph (d) the best technology, treatment technique, or other means available for achieving compliance with the maximum contaminant levels for all regulated PFAS identified in paragraph (c) of this section:
Contaminant | BAT |
---|---|
Hazard Index PFAS (HFPO-DA, PFBS, PFHxS, and PFNA) | Anion exchange, GAC, reverse osmosis, nanofiltration. |
HFPO-DA | Anion exchange, GAC, reverse osmosis, nanofiltration. |
PFHxS | Anion exchange, GAC, reverse osmosis, nanofiltration. |
PFNA | Anion exchange, GAC, reverse osmosis, nanofiltration. |
PFOA | Anion exchange, GAC, reverse osmosis, nanofiltration. |
PFOS | Anion exchange, GAC, reverse osmosis, nanofiltration. |
(e) The Administrator, pursuant to section 1412 of the Act, hereby identifies in table 4 to this paragraph (e) the affordable technology, treatment technique, or other means available to systems serving 10,000 persons or fewer for achieving compliance with the maximum contaminant levels for all regulated PFAS identified in paragraph (c) of this section:
Small system compliance technology 1 | Affordable for listed small system categories 2 |
---|---|
1 Section 1412(b)(4)(E)(ii) of SDWA specifies that SSCTs must be affordable and technically feasible for small systems. | |
2 The Act (ibid.) specifies three categories of small systems: (i) those serving 25 or more, but fewer than 501, (ii) those serving more than 500, but fewer than 3,301, and (iii) those serving more than 3,300, but fewer than 10,001. | |
3 “Technologies reject a large volume of water and may not be appropriate for areas where water quantity may be an issue. | |
Granular Activated Carbon | All size categories. |
Anion Exchange | All size categories. |
Reverse Osmosis, Nanofiltration 3 | 3,301-10,000. |
Effective date note: At 57 FR 22178, May 27, 1992, EPA postponed the effective date of §141.61(c)(2), (3), and (4) indefinitely pending agency reconsideration of these rules.
[56 FR 3593, Jan. 30, 1991, as amended at 56 FR 30280, July 1, 1991; 57 FR 31846, July 17, 1992; 59 FR 34324, July 1, 1994; 89 FR 32744, Apr. 26, 2024]
READ MORESHOW LESS
['Water Programs']
['Maximum Contaminant Levels', 'Water Quality', 'Safe Drinking Water']
Load More
J. J. Keller is the trusted source for DOT / Transportation, OSHA / Workplace Safety, Human Resources, Construction Safety and Hazmat / Hazardous Materials regulation compliance products and services. J. J. Keller helps you increase safety awareness, reduce risk, follow best practices, improve safety training, and stay current with changing regulations.
Copyright 2024 J. J. Keller & Associate, Inc. For re-use options please contact copyright@jjkeller.com or call 800-558-5011.