['Air Programs']
['Air Emissions']
03/15/2023
Copyright 2024 J. J. Keller & Associate, Inc. For re-use options please contact copyright@jjkeller.com or call 800-558-5011.
...
This section describes the emission testing you must perform to show compliance with the emission standards in §§1045.103 and 1045.105. See §1045.205(p) regarding emission testing related to the not-to-exceed standards. See §§1045.240 and 1045.245 and 40 CFR part 1065, subpart E, regarding service accumulation before emission testing.
(a) Select an emission-data engine from each engine family for testing as described in 40 CFR 1065.401. Select the engine with a configuration that is most likely to exceed the exhaust emission standards, using good engineering judgment. Consider the emission levels of all exhaust constituents over the full useful life of the engine when operated in a vessel.
(b) Test your emission-data engines using the procedures and equipment specified in subpart F of this part. In the case of dual-fuel engines, measure emissions when operating with each type of fuel for which you intend to certify the engine. In the case of flexible-fuel engines, measure emissions when operating with the fuel mixture that is most likely to cause the engine to exceed the applicable HC NOX emission standard, though you may ask us to exclude fuel mixtures that you can show are not likely to occur in use.
(c) We may measure emissions from any of your emission-data engines or other engines from the engine family, as follows:
(1) We may decide to do the testing at your plant or any other facility. If we do this, you must deliver the engine to a test facility we designate. The engine you provide must include appropriate manifolds, aftertreatment devices, electronic control units, and other emission-related components not normally attached directly to the engine block. If we do the testing at your plant, you must schedule it as soon as possible and make available the instruments, personnel, and equipment we need.
(2) If we measure emissions on one of your engines, the results of that testing become the official emission results for the engine. Unless we later invalidate these data, we may decide not to consider your data in determining if your engine family meets applicable requirements.
(3) We may set the adjustable parameters of your engine to any point within the physically adjustable ranges (see §1045.115(e)).
(4) We may calibrate your engine within normal production tolerances for anything we do not consider an adjustable parameter. For example, this would apply where we determine that an engine parameter is not an adjustable parameter (as defined in §1045.801) but that it is subject to production variability.
(d) You may ask to use carryover emission data from a previous model year instead of doing new tests, but only if all the following are true:
(1) The engine family from the previous model year differs from the current engine family only with respect to model year or other characteristics unrelated to emissions.
(2) The emission-data engine from the previous model year remains the appropriate emission-data engine under paragraph (b) of this section.
(3) The data show that the emission-data engine would meet all the requirements of this part that apply to the engine family covered by the application for certification.
(e) We may require you to test another engine of the same or different configuration in addition to the engine(s) tested under paragraph (b) of this section.
(f) If you use an alternate test procedure under 40 CFR 1065.10 and later testing shows that such testing does not produce results that are equivalent to the procedures specified in subpart F of this part, we may reject data you generated using the alternate procedure.
(g) Measure CO2 and CH4 with each low-hour certification test using the procedures specified in 40 CFR part 1065 starting in the 2011 and 2012 model years, respectively. Also measure N2O with each low-hour certification test using the procedures specified in 40 CFR part 1065 starting in the 2013 model year for any engine family that depends on NOX aftertreatment to meet emission standards. Small-volume engine manufacturers may omit measurement of N2O and CH4. These measurements are not required for NTE testing. Use the same units and modal calculations as for your other results to report a single weighted value for each constituent. Round the final values as follows:
(1) Round CO2 to the nearest 1 g/kW-hr.
(2) Round N2O to the nearest 0.001 g/kW-hr.
(3) Round CH4 to the nearest 0.001 g/kW-hr.
[73 FR 59194, Oct. 8, 2008, as amended at 74 FR 56510, Oct. 30, 2009; 86 FR 34514, Jun. 29, 2021]
READ MORESHOW LESS
['Air Programs']
['Air Emissions']
Load More
J. J. Keller is the trusted source for DOT / Transportation, OSHA / Workplace Safety, Human Resources, Construction Safety and Hazmat / Hazardous Materials regulation compliance products and services. J. J. Keller helps you increase safety awareness, reduce risk, follow best practices, improve safety training, and stay current with changing regulations.
Copyright 2024 J. J. Keller & Associate, Inc. For re-use options please contact copyright@jjkeller.com or call 800-558-5011.