...
(a) Chemical substance and significant new uses subject to reporting.(1) The chemical substance identified generically as N-(2-hydroxyethyl) alkenamide (PMN P-11-226) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this section do not apply to quantities of the PMN substance after they have been completely reacted (cured).
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in §721.63(a)(1), (a)(2)(i), (a)(3), (a)(4), (a)(6)(ii), (a)(6)(vi), (b), and (c). When determining which persons are reasonably likely to be exposed as required for §721.63(a)(1) and (4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible.
(A) The following gloves have been demonstrated to meet the requirements of §721.63(a)(3): North Silver Shield Gloves, Ansell Barrier Gloves, North Butyl Gloves, Ansell Chemi Pro Gloves, Ansell Neoprene Gloves, Ansell So-Vex, and Ansell Canners.
(B) The following National Institute for Occupational Safety and Health (NIOSH)-certified respirators with an Assigned Protection Factor (APF) of at least 1,000 meet the requirements of §721.63(a)(4):
(1) NIOSH-certified power air-purifying respirator with a hood or helmet and with appropriate gas/vapor (acid gas, organic vapor, or substance specific) cartridges in combination with HEPA filters.
(2) NIOSH-certified continuous flow supplied-air respirator equipped with a loose fitting face piece, hood, or helmet.
(3) NIOSH-certified negative pressure (demand) supplied-air respirator with a full face piece.
(C) As an alternative to the respiratory requirements listed here, a manufacturer or processor may choose to follow the New Chemical Exposure Limit (NCEL) provisions listed in the section TSCA 5(e) consent order for this substance. The NCEL is 0.03 mg/m3 as an 8-hour time weighted average verified by actual monitoring data.
(ii) Hazard communication program. Requirements as specified in §721.72(a), (b), (c), (d), (e), (f), (g)(1)(i), (g)(1)(iii), (g)(1)(iv), (g)(1)(vi), (g)(1)(vii), (g)(1)(viii), (g)(1)(ix), (g)(2)(i), (g)(2)(ii), and (g)(2)(iv) (use respiratory protection, or maintain workplace airborne concentrations at or below an 8-hour time-weighted average of 0.03 mg/m3), (g)(2)(v), (g)(3), and (g)(4). A significant new use of this substance is any manner or method of manufacture or processing associated with any use of this substance without providing risk notification as follows under §721.72(c):
(A) If as a result of the test data required under the TSCA section 5(e) consent order for this substance, the employer becomes aware that this substance may present a risk of injury to human health or the environment, the employer must incorporate this new information, and any information on methods for protecting against such risk, into a MSDS as described in §721.72(c) within 90 days from the time the employer becomes aware of the new information. If this substance is not being manufactured, processed, or used in the employer's workplace, the employer must add the new information to a MSDS before the substance is reintroduced into the workplace.
(B) The employer must ensure that persons who will receive the PMN substance from the employer, or who have received the PMN substance from the employer within 5 years from the date the employer becomes aware of the new information described in paragraph (a)(2)(i)(A) of this section, are provided an MSDS containing the information required under paragraph (a)(2)(i)(A) of this section within 90 days from the time the employer becomes aware of the new information.
(iii) Industrial, commercial, and consumer activities. Requirements as specified in §721.80(k) and (q).
(iv) Disposal. Requirements as specified in §721.85(a)(1) (destruction and removal efficiency of 99.99%), (a)(3) (underground injection control (class 1 well, deep well injection hazardous waste)), (b)(1) (destruction and removal efficiency of 99.99%), (b)(3) (underground injection control (class 1 well, deep well injection hazardous waste)), (c)(1) (destruction and removal efficiency of 99.99%), (c)(3) (underground injection control (class 1 well, deep well injection hazardous waste)).
(v) Release to water. Requirements as specified in §721.90(a)(1), (b)(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph (b).
(1) Recordkeeping. Recordkeeping requirements as specified in §721.125(a) through (k) are applicable to manufacturers and processors of these substances.
(2) Limitations or revocation of certain notification requirements. The provisions of §721.185 apply to this section.
(3) Determining whether a specific use is subject to this section. The provisions of §721.1725(b)(1) apply to paragraph (a)(2)(iii) of this section.
[79 FR 63834, Oct. 27, 2014]